Z-Wave factfile: GreenWave NS210-F

Information about specific Z-Wave devices
Post Reply
User avatar
ThinkPad
Posts: 1754
Joined: Tuesday 30 September 2014 8:49
Target OS: Linux
Domoticz version: beta
Location: The Netherlands
Contact:

Z-Wave factfile: GreenWave NS210-F

Post by ThinkPad » Friday 11 December 2015 23:28

Supplier:
Greenwave Reality (also sold as Nuon plugs in the past)

Website:
http://www.greenwavesystems.com/

Function:
Smart Plug with energy measurement

Z-Wave5
No

Rebranding:
Nuon E-manager Smartplug

Device Library from http://www.pepper1.net
http://www.pepper1.net/zwavedb/device/281

Manuals from manuals.zwaveeurope.com and doc.eedomus.com:
http://doc.eedomus.com/files/PowerNode_ ... nglish.pdf

Domoticz experience
Hardware:
Have send the plugs back, so from the top of my head:
- Switch device
- Watt device
- kWh device
Remarks:
- Needs constant polling, otherwise the LED on the unit will start blinking green. Very annoying if it is in your view (next to TV or so).
- It also only repeats for other Greenwave nodes, NOT for other Z-wave brands. So it is bad for improving the total strength of your Z-Wave mesh.
- Stability (or would the range cause this?) didn't seem to be very great, from the 4 plugs i bought, two of them regurarly fell out of the Z-wave network (timeouts, 'dropping command'). Even after excluding, resetting and including again. Strength of my network is not the issue, it has clear view to a Aeon motion 4m away.

Configuration:
Plugs send back, don't know this anymore. Maybe someone else can post this info.

Devices
Plugs send back, don't know this anymore. Maybe someone else can post this info.

zwcfg_0xaaaaaaa.xml sample:
Plugs send back, don't know this anymore. Maybe someone else can post this info.

Conclusion
Very cheap available at ROBBshop, but i wouldn't advise them because they need constant polling, don't increase the whole strength of your network and they didn't seem to be rocksolid. I had 4 of them, but send them back for a refund because of above reasons.
ThinkTheme - theme for Domoticz
My (Dutch) blog: http://thinkpad.tweakblogs.net - My Domoticz scripts: Bitbucket
I'm not (very) active anymore on this forum as i don't use Domoticz anymore.

User avatar
jannl
Posts: 901
Joined: Thursday 02 October 2014 6:36
Target OS: Raspberry Pi
Domoticz version: Beta
Location: Geleen
Contact:

Re: Z-Wave factfile: GreenWave NS210-F

Post by jannl » Saturday 12 December 2015 11:15

The one they sell now is the 310. I have one at home, not tested yet. According to the manual the powerstate can be configured. I also have one 210. No problems so far (about 2 weeks)

wmn79
Posts: 63
Joined: Monday 13 April 2015 23:19
Target OS: NAS (Synology & others)
Domoticz version: 3.5033
Location: Amsterdam, The Netherlands
Contact:

Re: Z-Wave factfile: GreenWave NS210-F

Post by wmn79 » Sunday 03 April 2016 21:09

More information on the settings for this device:

- parameter 0: Power change required to send a notification, in % from 1 to 100, default 10
- parameter 1: Keep alive time, in minutes from 1 to 255, default 2
- parameter 2: Color wheel selection, read only
- parameter 3: State after power loss, 0 = all off, 1 = remember last state, 2 = all on, default 2
- parameter 4: Led for network error, 0 = disable, 1 = enable, default 0
- association group 1: Color wheel change
- association group 2: Relay health
- association group 3: Power value change
- association group 4: Over-current protection

Documentation:
Technical doc for PowerNode

Parameter 3 and 4 seem only to work on devices with a firmware with Protocol Version: 3.41 and Application Version: 4.27 or higher.

Credits: vrampal

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest