Milight t2 wall switch cct

433Mhz opensource Receiver & Transmitter.

Moderator: Stuntteam

Post Reply
12345caravan
Posts: 40
Joined: Friday 31 October 2014 10:05
Target OS: Linux
Domoticz version:
Contact:

Milight t2 wall switch cct

Post by 12345caravan » Tuesday 23 January 2018 23:23

I'm having problems with my milight t2 wall switch adding to domoticz.
Accept new hardware, push button on wall switch, rflink/domoticz adds new device.
But when I use the new device nothing happens.
Domoticz only see the device switching off when i use the wall switch.
What goes wrong over here?
Attachments
t2-switch.jpg
t2-switch.jpg (120.09 KiB) Viewed 1257 times

12345caravan
Posts: 40
Joined: Friday 31 October 2014 10:05
Target OS: Linux
Domoticz version:
Contact:

Re: Milight t2 wall switch cct

Post by 12345caravan » Sunday 04 February 2018 20:13

Nobody else using this switch?
Rflink is sending the following command when switching: 10;MiLightv1;02b2;01;0000;ON
Is this correct?
Just adding another switch T2 CCT, and thsi one isn't working either....
Rflink picks up the signal in domoticz, add device, but no response.
I can pair the bulbs in domoticz, but i want also use the switch.

tontze
Posts: 335
Joined: Thursday 12 January 2017 16:30
Target OS: Raspberry Pi
Domoticz version:
Contact:

Re: Milight t2 wall switch cct

Post by tontze » Monday 05 March 2018 20:31

Do you have "learn new device" enabled in domoticz settings, and enabled milight in rflink ? You need to also pair bulp with the switch.
-----------------------------------------
Rpi 3 / Razberry 2
RFLink 433mhz / Nrf 2.4Ghz
Mi Light
ESP82xx

12345caravan
Posts: 40
Joined: Friday 31 October 2014 10:05
Target OS: Linux
Domoticz version:
Contact:

Re: Milight t2 wall switch cct

Post by 12345caravan » Tuesday 06 March 2018 15:43

Yes did that, domoticz can see the new switch, but the rflink is sending a total different command as the wall switch, so this is not working.
I f I give the wall switch command through the rflink command line in domoticz, it is working.
Hope this will be supported in next rflink release.....

User avatar
Stuntteam
Posts: 437
Joined: Wednesday 06 May 2015 16:39
Target OS: Raspberry Pi
Domoticz version:
Contact:

Re: Milight t2 wall switch cct

Post by Stuntteam » Wednesday 07 March 2018 1:07

Can you send me the commands that you logged?
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic RFLink Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8

tontze
Posts: 335
Joined: Thursday 12 January 2017 16:30
Target OS: Raspberry Pi
Domoticz version:
Contact:

Re: Milight t2 wall switch cct

Post by tontze » Monday 23 April 2018 7:00

Little late, but i did pair switch with bulbps, and thebn learned that switch press on domoticz.
-----------------------------------------
Rpi 3 / Razberry 2
RFLink 433mhz / Nrf 2.4Ghz
Mi Light
ESP82xx

Post Reply

Who is online

Users browsing this forum: No registered users and 4 guests