Trying to use Popp 009303 Battery Wall Controller with Domoticz

Topics (not sure which fora)
when not sure where to post, post here and mods will move it to right forum.
Letalis
Posts: 9
Joined: Monday 28 November 2016 22:21
Target OS: Raspberry Pi
Domoticz version:
Contact:

Trying to use Popp 009303 Battery Wall Controller with Domoticz

Postby Letalis » Thursday 08 December 2016 0:09

Hi all,
I need some starting help to get on track with Domoticz.
I have included a Popp 009303 Battery Wall Controller to Domotics but need some help to configure this to work with my qubino in the kitchen.
Both on/off and dim.

On Controller
Controller Popp del1.PNG
Controller Popp del1.PNG (275.18 KiB) Viewed 423 times

Controller Popp del2.PNG
Controller Popp del2.PNG (124.54 KiB) Viewed 423 times


On Device
Device Popp.PNG
Device Popp.PNG (18.43 KiB) Viewed 423 times

Letalis
Posts: 9
Joined: Monday 28 November 2016 22:21
Target OS: Raspberry Pi
Domoticz version:
Contact:

Re: Trying to use Popp 009303 Battery Wall Controller with Domoticz

Postby Letalis » Friday 09 December 2016 20:15

FYI: I can use it in Z-wave.me where I can see all 4 buttons.

Letalis
Posts: 9
Joined: Monday 28 November 2016 22:21
Target OS: Raspberry Pi
Domoticz version:
Contact:

Re: Trying to use Popp 009303 Battery Wall Controller with Domoticz

Postby Letalis » Tuesday 27 December 2016 11:24

Am I alone on trying to use this one?

Stromsec
Posts: 2
Joined: Tuesday 27 December 2016 12:00
Target OS: Linux
Domoticz version:
Contact:

Re: Trying to use Popp 009303 Battery Wall Controller with Domoticz

Postby Stromsec » Tuesday 27 December 2016 12:06

Hi, I have also been struggling with this one.
Got it working today by following this guide https://www.domoticz.com/wiki/Popp_Kfob
Skip the first 2 sections and start at "Adding the Popp Kfob to Domoticz" "3. Add the Controller (Node 1, the zwave USB stick) to all groups of the Kfob"
After this i could successfully add buttons to a scene.

Remember to wake up the popp by go to maintenance mode by pressing all for buttons (flashing green light) and the press button 2 (upper right) this will allow the popp to fetch the new settings.

Letalis
Posts: 9
Joined: Monday 28 November 2016 22:21
Target OS: Raspberry Pi
Domoticz version:
Contact:

Re: Trying to use Popp 009303 Battery Wall Controller with Domoticz

Postby Letalis » Tuesday 27 December 2016 14:20

Stromsec wrote:Hi, I have also been struggling with this one.
Got it working today by following this guide https://www.domoticz.com/wiki/Popp_Kfob
Skip the first 2 sections and start at "Adding the Popp Kfob to Domoticz" "3. Add the Controller (Node 1, the zwave USB stick) to all groups of the Kfob"
After this i could successfully add buttons to a scene.

Remember to wake up the popp by go to maintenance mode by pressing all for buttons (flashing green light) and the press button 2 (upper right) this will allow the popp to fetch the new settings.


Thanks . Now I'm on the way to make this work.
Did you get a "shitload" of lightswitches aswell?

Stromsec
Posts: 2
Joined: Tuesday 27 December 2016 12:00
Target OS: Linux
Domoticz version:
Contact:

Re: Trying to use Popp 009303 Battery Wall Controller with Domoticz

Postby Stromsec » Wednesday 28 December 2016 10:05

I only got 4 new devices one for each button.
What are your settings on the popp? I have the same as the ones in the link I provided.

Letalis
Posts: 9
Joined: Monday 28 November 2016 22:21
Target OS: Raspberry Pi
Domoticz version:
Contact:

Re: Trying to use Popp 009303 Battery Wall Controller with Domoticz

Postby Letalis » Wednesday 28 December 2016 22:37

same here.

singleclick
doubleclick
longclick
and a fourth similar to a releaseclick.

When I longclick and release it gives me 2 different devices.

swevm
Posts: 19
Joined: Friday 16 September 2016 20:04
Target OS: Raspberry Pi
Domoticz version: 7067
Location: Sweden
Contact:

Re: Trying to use Popp 009303 Battery Wall Controller with Domoticz

Postby swevm » Monday 02 January 2017 13:48

For me devices only show up in Domoticz if I configure buttons to send "scene command".
What I´d love to have is the same learning capabilities that exist for RFX/Tellstick in Domoticz. but that seem not to work for Z-Wave remotes.

Keep in mind that even if you get a device from the Popp remote you cannot interact with is as it´s only capable of sending a state change command, not recieve anything - This mean you cannot interact with the devices that Domotics create for the remote. Also 009303 remotes seem only capable of sending "On" command if configured to send "scene command".

/Magnus
Domoticz on RPi3 with Razberry: 10xZME WALLC-S, 10x Fib Switch, 6x Fib Wallplug, 1x Fib Motion Sensor, 1x Fib Smoke Sensor, 1x Fib Universal sensor (with 1-wire), 3x SwiidInter cordsw,ESPEasy [1-wire and relay], Kodi, Node-Red [Onkyo NR-828, UI etc]

soroga
Posts: 1
Joined: Monday 02 January 2017 13:54
Target OS: -
Domoticz version:
Contact:

Re: Trying to use Popp 009303 Battery Wall Controller with Domoticz

Postby soroga » Monday 02 January 2017 14:05

What are your settings ?
Thanks
for more information about soroga Caviar go to http://negineabzian.com/fa-ir/%D8%AE%D8 ... 1/CatID/27

swevm
Posts: 19
Joined: Friday 16 September 2016 20:04
Target OS: Raspberry Pi
Domoticz version: 7067
Location: Sweden
Contact:

Re: Trying to use Popp 009303 Battery Wall Controller with Domoticz

Postby swevm » Wednesday 11 January 2017 0:08

Took some time to look into this - busy at work
Have updated to latest beta, 6306.


Button configurations I have tested and how they are seen by Domoticz:
"Switch On/Off" - Can control zwave Groups but is not recognized by Domoticz if pressed. However the controlled device state change gets intercepted by Domoticz so it can be used to trigger Domoticz scenes
"Send Scenes" - A device is created by Domoticz when button is pressed on 009303 - This device can be used to trigger Domoticz scenes using Switch|Learn if needed (keep in mind it only send "On" command) - Have noticed that once I change config back to normal On/Off setting created device is still there and I cannot delete it
"Central scene to gateway" - Nothing is detected at all by Domoticz

For me its not how I want it to work as I want to stay independent of Domoticz itself to control zwave devices but still be able to use Domoitcz to trigger state change of other z-wave devices when needed while being able to intercept when a remote button is pressed even if its using basic On/Off configuration. Hence I use zwave groups to allow my zwave remotes to control other zwave devices even if Domoticz is down. Need to stay WifeCompatible.

/Magnus
Domoticz on RPi3 with Razberry: 10xZME WALLC-S, 10x Fib Switch, 6x Fib Wallplug, 1x Fib Motion Sensor, 1x Fib Smoke Sensor, 1x Fib Universal sensor (with 1-wire), 3x SwiidInter cordsw,ESPEasy [1-wire and relay], Kodi, Node-Red [Onkyo NR-828, UI etc]


Return to “Other questions and discussions”

Who is online

Users browsing this forum: No registered users and 2 guests