no ID, no TYPE for ZWave devices (ID = 0x0000, TYPE = 0x0000)

For Z-Wave related questions in Domoticz
Post Reply
altarus1
Posts: 3
Joined: Tuesday 19 December 2017 13:17
Target OS: Linux
Domoticz version: 3.8153
Contact:

no ID, no TYPE for ZWave devices (ID = 0x0000, TYPE = 0x0000)

Post by altarus1 » Tuesday 19 December 2017 13:55

Hello,

I've used domoticz since one year on raspberry but I would migrate this on linux.

I've installed domoticz on fresh linux following wiki page for linux install (http://www.domoticz.com/wiki/Linux)

Please note that OS is a virtual machine, but USB device (RFXtrx433 and ZWave dongle are mounted and seen by system).
After install, I've restored domoticz db to new system saved from the raspberry

The install seems to be fine, Domoticz runs normally and there is no pb with RFXcom, script... . But, except zwave controller (Aetoec Z-Stick Gen5), all devices haven't IDs, nor TYPEs. And so, none values are recorded (devices seems to be unseen)
Clipboard 1.jpg
Clipboard 1.jpg (154.62 KiB) Viewed 768 times
Clipboard 2.jpg
Clipboard 2.jpg (192.56 KiB) Viewed 768 times
try searching solution in this forum, found some topics wich describe sames issues with recent release of Domoticz, then I have done new compil from last stable release (v3.8153) which is the same release of my Domoticz install on Raspberry.
I also try "Refresh Node Info" from OZW control panel but didn't resolve issue (give ERROR: Dropping command, expected response not received...)

Nodes topology seem to be ok

Someone could help me ?

User avatar
philchillbill
Posts: 230
Joined: Monday 12 September 2016 13:47
Target OS: Linux
Domoticz version: beta
Location: Eindhoven. NL
Contact:

Re: no ID, no TYPE for ZWave devices (ID = 0x0000, TYPE = 0x0000)

Post by philchillbill » Tuesday 19 December 2017 14:03

I had it in the past and it magically stopped happening a while back. The temporary fix at the time was to delete the ozwcpxxx xml file in your /Config directory and reboot.


Sent from my iPhone using Tapatalk
NUC/Ubuntu, Evohome Heating + HGI80, Evohome Security, 4x HikVision IP cams, Aeotec, Neo & Fibaro Z-Wave, Logitech Media Server (on Synology DS916+), 10x SqueezeBox, Kodi, Harmony Hub, 5x Amazon Echo, HA-Bridge, Hue.

altarus1
Posts: 3
Joined: Tuesday 19 December 2017 13:17
Target OS: Linux
Domoticz version: 3.8153
Contact:

Re: no ID, no TYPE for ZWave devices (ID = 0x0000, TYPE = 0x0000)

Post by altarus1 » Tuesday 19 December 2017 14:18

Thank you philchillbill for your answer.

I try it by renaming zwcfg_XXX.xml file (in Config dir), then reboot. After reboot, device aren't still not identified. A new xml config file is created, I open it, ID and TYPE are set to 0

ropske
Posts: 315
Joined: Tuesday 12 August 2014 5:37
Target OS: Raspberry Pi
Domoticz version: V3_8394
Location: Rumbeke,Belgium
Contact:

Re: no ID, no TYPE for ZWave devices (ID = 0x0000, TYPE = 0x0000)

Post by ropske » Tuesday 19 December 2017 14:38

Your device_manufacturer.xml is not up to date i think


Verzonden vanaf mijn iPhone met Tapatalk

altarus1
Posts: 3
Joined: Tuesday 19 December 2017 13:17
Target OS: Linux
Domoticz version: 3.8153
Contact:

Re: no ID, no TYPE for ZWave devices (ID = 0x0000, TYPE = 0x0000)

Post by altarus1 » Tuesday 19 December 2017 15:06

ropske wrote:
Tuesday 19 December 2017 14:38
Your device_manufacturer.xml is not up to date i think
I didn't find any device_manufacturer.xml file, did you mean manufacturer_specific.xml in Config dir ? I open it, and it seem to include my devices (note that I didn't have exotic devices, only Aeotec multisensor and fibaro plugs)

If not, where can I find this file, and how can I update it ?

hestia
Posts: 17
Joined: Tuesday 26 December 2017 0:06
Target OS: Raspberry Pi
Domoticz version: 4.9700
Location: Paris
Contact:

Re: no ID, no TYPE for ZWave devices (ID = 0x0000, TYPE = 0x0000)

Post by hestia » Tuesday 26 December 2017 0:15

hello
I've the same issue when including new z-wave hardware, no device are visible.
I had a beta version about 1 month old, as it didn't work, I've upgraded today with Version: 3.8796. And it's the same :-(
Any other ideas? Isn't it a bug of this beta?

hestia
Posts: 17
Joined: Tuesday 26 December 2017 0:06
Target OS: Raspberry Pi
Domoticz version: 4.9700
Location: Paris
Contact:

Re: no ID, no TYPE for ZWave devices (ID = 0x0000, TYPE = 0x0000)

Post by hestia » Sunday 31 December 2017 0:31

hestia wrote:
Tuesday 26 December 2017 0:15
hello
I've the same issue when including new z-wave hardware, no device are visible.
I had a beta version about 1 month old, as it didn't work, I've upgraded today with Version: 3.8796. And it's the same :-(
Any other ideas? Isn't it a bug of this beta?
Hi
some news:
the case that doesn't work is when I try to include a device with the Z-wave stick( Aeotec ZW090 Z-Stick Gen5 EU) unplugged from the domoticz server (PI)
When I include it near the PI and with the Z-wave stick plugged it works fine!

Post Reply

Who is online

Users browsing this forum: Google [Bot] and 1 guest