Etekcity Smart Wireless Electrical Outlet

Others (MiLight, Hue, Toon etc...)
Post Reply
tedmtl
Posts: 3
Joined: Sunday 03 April 2016 15:00
Target OS: Raspberry Pi
Domoticz version: v3.5641
Location: Canada
Contact:

Etekcity Smart Wireless Electrical Outlet

Post by tedmtl » Wednesday 14 September 2016 13:32

Hi,

I have bought a Etekcity Smart Wireless Electrical Outlet from amazon.ca (https://www.amazon.ca/Etekcity-Wireless ... cal+Outlet)

i try to control it from domoticz through Rfrxtrx433,

In RFXmngr, i can turn on and off the outlet (housecode=H, unitcode=1-3)

By can't add it as dimmer to domoticz, only housecodes A to D are available for Energenie 5-gang ?
================================================
Lighting1 command
================================================
Packettype = Lighting1
subtype = Energenie 5-gang, Etekcity
Sequence nbr = 3
housecode = H
unitcode = 3
Command = Off
Signal level = 0 -120dBm

is there a way to get it work in domoticz ?
Attachments
2016-09-14 07_29_45-Domoticz - Internet Explorer.png
2016-09-14 07_29_45-Domoticz - Internet Explorer.png (21.08 KiB) Viewed 1284 times

apm
Posts: 37
Joined: Wednesday 28 May 2014 1:09
Target OS: Raspberry Pi
Domoticz version:
Contact:

Re: Etekcity Smart Wireless Electrical Outlet

Post by apm » Monday 13 February 2017 23:48

Did you get this working at all ?
--
RPi + RFXCOM
Lightwave RF, ByeByeStandby, Generic Temp sensors, OWL, TRC02 RGB Controllers, HIVE
Next Projects: Rain sensor, Cameras.

apm
Posts: 37
Joined: Wednesday 28 May 2014 1:09
Target OS: Raspberry Pi
Domoticz version:
Contact:

Re: Etekcity Smart Wireless Electrical Outlet

Post by apm » Tuesday 14 February 2017 1:54

After some fiddling I got mine working on latest firmware 1015 and latest Domoticz beta 3.6707 - it will not auto-detect but manual switch adding works fine - you might have to change the house number settings "J" worked for mine perfectly http://imgur.com/a/dQOzh
--
RPi + RFXCOM
Lightwave RF, ByeByeStandby, Generic Temp sensors, OWL, TRC02 RGB Controllers, HIVE
Next Projects: Rain sensor, Cameras.

morilm
Posts: 30
Joined: Friday 27 January 2017 13:57
Target OS: OS X
Domoticz version:
Contact:

Re: Etekcity Smart Wireless Electrical Outlet

Post by morilm » Tuesday 14 February 2017 17:46

I have received a 5pack today.

I have been able to auto create the switch automatically (using Rflink usb on a Pi3). The devices are detected as TriState.

regards,
Miguel

HM31
Posts: 16
Joined: Friday 04 August 2017 16:13
Target OS: NAS (Synology & others)
Domoticz version:
Contact:

Re: Etekcity Smart Wireless Electrical Outlet

Post by HM31 » Thursday 14 December 2017 3:14

Received a pack of 5 this week. Couldn't have it added automaticaly (Domoticz Version: 3.7324 and RFXCOM - RFXtrx433 USB 433.92MHz Transceiver Version: Ext/1015).

Found Housecode A and unitcode 5 or 10 can control all the plugs at once (on and off) but couldn't find a way to control each of them.

HM31
Posts: 16
Joined: Friday 04 August 2017 16:13
Target OS: NAS (Synology & others)
Domoticz version:
Contact:

Re: Etekcity Smart Wireless Electrical Outlet

Post by HM31 » Thursday 04 January 2018 14:38

Contacted RFXCOM team, my model is not supported :

"The supported version is a P300 type and your version is a ?Rx type.
The Etekcity P300 remote is not received but you could add the Energenie5 device as an additional remote to the module."

Then I put each of the plugs in learning mode, one by one, and send each of them the house-unit combination I decided for each of them and it works. It was added has another remote, it didn't replace actual remote. Thus I can use each of the remote using Domoticz and the genuine remote.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest