Manually set the alarm of a Fibaro Smoke Detector

Must be cleaned all topics go to the right subforum
User avatar
Marq
Posts: 25
Joined: Sunday 26 April 2015 12:26
Target OS: Raspberry Pi
Domoticz version:
Location: The Netherlands
Contact:

Manually set the alarm of a Fibaro Smoke Detector

Postby Marq » Sunday 10 January 2016 19:08

Hi,
I have a Fibaro FGSD-002 Smoke Detector.
Is it possible to let it act as an alarm ?
(in other words, let the alarm go off manually / by scripting ?)
Thanks,
Mark

User avatar
Marq
Posts: 25
Joined: Sunday 26 April 2015 12:26
Target OS: Raspberry Pi
Domoticz version:
Location: The Netherlands
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby Marq » Thursday 21 January 2016 22:57

Nobody ??

User avatar
nayr
Posts: 431
Joined: Tuesday 11 November 2014 19:42
Target OS: Linux
Domoticz version: github
Location: Denver, CO - USA
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby nayr » Thursday 21 January 2016 23:04

no, these devices are not switchable.. its functionally much like a motion sensor, it can tell you there is motion but you cant tell it there is motion.
Debian Jessie: CuBox-i4 (Primary) w/Static Routed IP and x509 / BeagleBone with OpenSprinkler / BeagleBone Planted Aquarium / 3x Raspbery Pi2b GPIO Slaves
Elemental Theme - node-domoticz-mqtt - Home Theatre Controller - AndroidTV Simple OSD Remote - x509 TLS Auth

Kohen
Posts: 26
Joined: Monday 12 October 2015 12:05
Target OS: NAS (Synology & others)
Domoticz version:
Location: Veldhoven, The Netherlands
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby Kohen » Monday 01 February 2016 20:10

so there is no way to control the smoke sensor ? Or not yet?
Synology NAS 412+, Aeotec stick V5, Aeotec recessed door sensor, Aeotec micro double smart switch, Fibaro Dimmer, iPad 2 with own 3d printed wall mount.

User avatar
nayr
Posts: 431
Joined: Tuesday 11 November 2014 19:42
Target OS: Linux
Domoticz version: github
Location: Denver, CO - USA
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby nayr » Monday 01 February 2016 21:42

it was never designed to do what you want... so no way.
Debian Jessie: CuBox-i4 (Primary) w/Static Routed IP and x509 / BeagleBone with OpenSprinkler / BeagleBone Planted Aquarium / 3x Raspbery Pi2b GPIO Slaves
Elemental Theme - node-domoticz-mqtt - Home Theatre Controller - AndroidTV Simple OSD Remote - x509 TLS Auth

Kohen
Posts: 26
Joined: Monday 12 October 2015 12:05
Target OS: NAS (Synology & others)
Domoticz version:
Location: Veldhoven, The Netherlands
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby Kohen » Monday 01 February 2016 21:45

but i want to! .. i 'm looking for a device what can make sound. replacing my door chime. smoke detector would be best because i have them everywhere so i have the sound everywhere i need it :)

other suggestions?
Synology NAS 412+, Aeotec stick V5, Aeotec recessed door sensor, Aeotec micro double smart switch, Fibaro Dimmer, iPad 2 with own 3d printed wall mount.

User avatar
nayr
Posts: 431
Joined: Tuesday 11 November 2014 19:42
Target OS: Linux
Domoticz version: github
Location: Denver, CO - USA
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby nayr » Monday 01 February 2016 21:51

Z-Wave chimes suck, I feel your pain.. and not really, there is a new chime out but its not fully functional last I checked.. its only working as a alarm siren, none of the other sounds seem to be functioning, yet.

personally I plan on just adding a relay to fire off alternate ringger on my wired doorbell, its got an unused chime for a back door that I think I'll steal for system alerts like the mailbox or gates opening... there is a MiMo Z-Wave device that could do this job if you want to stick with Z-Wave.. but I doubt it'll fit in your doorbell housing so wiring may still be required.
Debian Jessie: CuBox-i4 (Primary) w/Static Routed IP and x509 / BeagleBone with OpenSprinkler / BeagleBone Planted Aquarium / 3x Raspbery Pi2b GPIO Slaves
Elemental Theme - node-domoticz-mqtt - Home Theatre Controller - AndroidTV Simple OSD Remote - x509 TLS Auth

manwe
Posts: 12
Joined: Thursday 04 February 2016 15:02
Target OS: Raspberry Pi
Domoticz version:
Location: Switzerland
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby manwe » Thursday 04 February 2016 16:00

You could use a Z-Wave Switch to set something on Fire :lol:

User avatar
Marq
Posts: 25
Joined: Sunday 26 April 2015 12:26
Target OS: Raspberry Pi
Domoticz version:
Location: The Netherlands
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby Marq » Saturday 06 February 2016 11:38

My question was triggered by this remark in the manual:
Sending the notification ALARM SENSOR REPORT (TYPE = SMOKE ALARM) to associated devices once smoke is detected. Up to five devices supporting fire alarm command may be included in this group


I interpret this, that through association, one smoke detector can trigger the alarm of associated smoke detectors.

Is there a way to use this, to fool :mrgreen: the smoke detector, and trigger the alarm by Domoticz ?

User avatar
nayr
Posts: 431
Joined: Tuesday 11 November 2014 19:42
Target OS: Linux
Domoticz version: github
Location: Denver, CO - USA
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby nayr » Saturday 06 February 2016 22:02

no... but lets pretend you could.. every time the door opens you want your smoke alarms giong off? wtf.. I doubt you'll have the ability to shut them off without walking up to them and pushing the button.. most tamper and security alarms in z-wave can only be triggered on, the device will go back to a normal state on its own and no commands will help you reset the alarm.

just give it up already.. hooking a smoke alarm up to your front door is asinine.

If you need to drive a nail, try using a Hammer instead of your face.. You'll find life is easy when you use the right tool for the job... so go buy a freaking alarm/chime that you can instruct to go on/off.
Debian Jessie: CuBox-i4 (Primary) w/Static Routed IP and x509 / BeagleBone with OpenSprinkler / BeagleBone Planted Aquarium / 3x Raspbery Pi2b GPIO Slaves
Elemental Theme - node-domoticz-mqtt - Home Theatre Controller - AndroidTV Simple OSD Remote - x509 TLS Auth

User avatar
Marq
Posts: 25
Joined: Sunday 26 April 2015 12:26
Target OS: Raspberry Pi
Domoticz version:
Location: The Netherlands
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby Marq » Saturday 20 February 2016 11:43

nayr wrote: If you need to drive a nail, try using a Hammer instead of your face.. You'll find life is easy when you use the right tool for the job...

There are people who drive nails into their head, and become creative of it... perhaps something for you to try ?

Why buy a new alarm if you have several hanging around the house ?

User avatar
nayr
Posts: 431
Joined: Tuesday 11 November 2014 19:42
Target OS: Linux
Domoticz version: github
Location: Denver, CO - USA
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby nayr » Saturday 20 February 2016 12:22

This thread is making me really consider it..

They are not ZWave alarms, they are sensor inputs that happen have a local Alarm.. no output is exposed so your shit out of luck bro. Input != Output
Debian Jessie: CuBox-i4 (Primary) w/Static Routed IP and x509 / BeagleBone with OpenSprinkler / BeagleBone Planted Aquarium / 3x Raspbery Pi2b GPIO Slaves
Elemental Theme - node-domoticz-mqtt - Home Theatre Controller - AndroidTV Simple OSD Remote - x509 TLS Auth

mchris
Posts: 1
Joined: Wednesday 11 January 2017 12:50
Target OS: Linux
Domoticz version:
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby mchris » Wednesday 11 January 2017 12:58

Old thread, but still I have an idéa:
Maybe you could use the Excess Temperature Warning. When you want to trigger the alarm - set it to one degree celcius (not zero, which disables the function), afterwards set it back (default 55 degrees).
Question is how to make it react quickly since it normally sleeps and takes a while to react to parameter changes...

Egregius
Posts: 1919
Joined: Thursday 09 April 2015 12:19
Target OS: NAS (Synology & others)
Domoticz version: 3.5877
Location: Beitem, BE
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby Egregius » Wednesday 11 January 2017 13:06

Buy a siren, no hassle.
Fibaro smoke detectors aren't designed for this functionnality.

antares
Posts: 47
Joined: Saturday 24 September 2016 9:25
Target OS: Raspberry Pi
Domoticz version: beta
Location: Germany
Contact:

Re: Manually set the alarm of a Fibaro Smoke Detector

Postby antares » Sunday 22 January 2017 14:52

You can use the Popp smoke detectors that also come with a separate siren.


Return to “Scripts [cleaning in progress]”

Who is online

Users browsing this forum: No registered users and 1 guest