Search found 342 matches

by b_weijenberg
Saturday 19 August 2017 10:38
Forum: Bugs and Problems
Topic: RFXTRX433E Panic
Replies: 9
Views: 259

Re: RFXTRX433E Panic

Disable automatic adding of new devices in Domoticz!

There is a RF device that transmits data with the same format as the RM174RF. This is decoded by the Ext2 firmware with ARC enabled.
by b_weijenberg
Saturday 19 August 2017 9:19
Forum: Bugs and Problems
Topic: RFXTRX433E Panic
Replies: 9
Views: 259

Re: RFXTRX433E Panic

Enable only protocols you need to receive your devices.

Disable the ARC protocol as the packets a most probably decoded as RM174RF or use Ext firmware.
by b_weijenberg
Wednesday 09 August 2017 9:58
Forum: Other questions and discussions
Topic: RFXCOM Rollertrol (T0) and AC114 Blinds not working
Replies: 10
Views: 299

Re: RFXCOM Rollertrol (T0) and AC114 Blinds not working

After you have configured the BlindsT0 motor using Type2 you can flash Ext2 and control the motor. Or keep using Type2 with BlindsT0 disabled if the protocols you need are present in Type2. Enabling BlindsT0 will disable all other protocols. The function to receive BlindsT0 is only to receive the re...
by b_weijenberg
Tuesday 08 August 2017 20:37
Forum: Other questions and discussions
Topic: RFXCOM Rollertrol (T0) and AC114 Blinds not working
Replies: 10
Views: 299

Re: RFXCOM Rollertrol (T0) and AC114 Blinds not working

That's not correct! You must use Type2 not Ext2.
After you have added the BlindsT0 remote you can use Ext2 firmware to control the motor.
by b_weijenberg
Tuesday 08 August 2017 17:26
Forum: Other questions and discussions
Topic: RFXCOM Rollertrol (T0) and AC114 Blinds not working
Replies: 10
Views: 299

Re: RFXCOM Rollertrol (T0) and AC114 Blinds not working

Did you use Type2 firmware with BlindsT0 enabled?
by b_weijenberg
Tuesday 08 August 2017 12:42
Forum: Other questions and discussions
Topic: RFXCOM Rollertrol (T0) and AC114 Blinds not working
Replies: 10
Views: 299

Re: RFXCOM Rollertrol (T0) and AC114 Blinds not working

I suppose something has changed in the Unit Code.
Please check with RFXmngr if the motor can be controlled using the same ID and Unit code or maybe a different Unit code.
by b_weijenberg
Friday 04 August 2017 11:54
Forum: Rfxcom Transceiver
Topic: Rfxcom lost transmission power
Replies: 12
Views: 870

Re: Rfxcom lost transmission power

Hi i had brakedown on my secont rfxcom433e after lightenibg storm eaven if det storm was not too near seems like det receiver damaged it sends comands ok any see this problem Transmit power is OK. It is possible that the receiver is damaged by a lightning pulse. Please check the RFXtrx on another l...
by b_weijenberg
Sunday 30 July 2017 16:14
Forum: Rfxcom Transceiver
Topic: AMST-606 Door contacts
Replies: 5
Views: 223

Re: AMST-606 Door contacts

Please check with RFXmngr if the sensor is correct received with only the AC protocol enabled.
The timers are not enabled in the sensors?
by b_weijenberg
Sunday 30 July 2017 13:53
Forum: Rfxcom Transceiver
Topic: AMST-606 Door contacts
Replies: 5
Views: 223

Re: AMST-606 Door contacts

Try with only the AC protocol enabled and check if the sensors are correct received.
by b_weijenberg
Sunday 30 July 2017 13:49
Forum: Rfxcom Transceiver
Topic: When is a Rfxcom needed?
Replies: 3
Views: 249

Re: When is a Rfxcom needed?

ESP/WiFi operates at 2.4GHz and cannot be used in conjunction with the RFXtrx433E.
The RFXCOM can be used for 433.92MHz devices, 433.42MHz Somfy RTS and MCZ pellet stove at 434.50MHz
Please see chapter 2 in the RFXtrx User Guide for the full list of supported devices by the RFXtrx433E.
by b_weijenberg
Friday 28 July 2017 21:46
Forum: Rfxcom Transceiver
Topic: There is Somfy in the air!!
Replies: 115
Views: 38843

Re: There is Somfy in the air!!

The RFXtrx433E is flashed with Ext or Ext2 firmware?
The red LED is blinking on the RFXtrx433E (indicating is transmits the RF command) if you press the Test button?
Are you able to control the Somfy screen with the Telis remote at the same location as the RFXtrx433E antenna?
by b_weijenberg
Thursday 20 July 2017 10:31
Forum: Rfxcom Transceiver
Topic: Rfxcom stops working
Replies: 1
Views: 167

Re: Rfxcom stops working

It seems the FTDI USB interface is locked. In most cases this is due to a spike on the power or a bad RPI power supply.
Possible solutions:
Do not run the USB cable along power lines,
Use a good quality power supply,
Connect the RFXtrx to a powered USB hub (with a good quality power supply).
by b_weijenberg
Monday 17 July 2017 9:14
Forum: Other questions and discussions
Topic: Extend 433mhz coverage ?
Replies: 13
Views: 788

Re: Extend 433mhz coverage ?

You can use a second Raspberry PI with Domoticz or install ser2net to access the RFXtrx433E over LAN
See also http://www.domoticz.com/forum/viewtopic ... et#p125747
by b_weijenberg
Monday 17 July 2017 9:09
Forum: Rfxcom Transceiver
Topic: how can I connect Schellenberg garage door to Rfxcom
Replies: 1
Views: 191

Re: how can I connect Schellenberg garage door to Rfxcom

It seems the device is using an encrypted protocol "Scanveilige codering" and therefore not possible.
by b_weijenberg
Saturday 17 June 2017 11:29
Forum: Bugs and Problems
Topic: sunscreen with jolly Motor
Replies: 2
Views: 179

Re: sunscreen with jolly Motor

Never heard about Jolly. Can this motor also be controlled with a Somfy Telis4 remote?

If so, did you follow the instructions in chapter 9 of the RFXtrx User Guide?
by b_weijenberg
Friday 09 June 2017 15:37
Forum: Rfxcom Transceiver
Topic: ASA ETR Blids motor
Replies: 3
Views: 310

Re: ASA ETR Blinds motor

Yes, use the same procedure as Somfy RTS to add the device in Domoticz.
You can also use RFXmngr to pair the AS motor and use the same ID-Unit code in Domoticz as used in RFXmngr.
by b_weijenberg
Monday 29 May 2017 15:17
Forum: Rfxcom Transceiver
Topic: There is Somfy in the air!!
Replies: 115
Views: 38843

Re: There is Somfy in the air!!

I've been looking for an answer, but couldn't find it in the forum: I've got 4 sunscreens (Somfy). They all have a Somfy Smoove RTS Remote and they work. I've added the switches in Domomticz (Synology NAS) and that works (RFXCOM E) I've added a LUA script with Buienradar and a Blocky script to send...
by b_weijenberg
Friday 26 May 2017 8:53
Forum: Temperature and Weather
Topic: pool temperature sensor TFA 30.3216.20
Replies: 8
Views: 1780

Re: pool temperature sensor TFA 30.3216.20

check with RFXmngr if the sensor is received with only TFA enabled
by b_weijenberg
Monday 22 May 2017 22:30
Forum: Compatibility
Topic: Recommend UK remote sockets?
Replies: 3
Views: 392

Re: Recommend UK remote sockets?

Cotech is supported in Ext2 firmware http://www.clasohlson.com/uk/Cotech-Sma ... ck/18-1255
by b_weijenberg
Sunday 21 May 2017 12:40
Forum: Rfxcom Transceiver
Topic: Generic protocol to send distance measurement?
Replies: 2
Views: 333

Re: Generic protocol to send distance measurement?

Maybe you can use the RFXMeter protocol. Contact support rfxcom.com